Most additive manufacturing engineers working on structural drone airframes have hit a familiar constraint. HP’s Multi Jet Fusion can produce complex PA12 geometries with good dimensional accuracy, but for parts that need to handle cyclic loads or absorb impact without gaining mass, the mechanical properties of the base polymer may not always meet the requirements of high-performance applications.
Defense, aerospace, industrial UAVs, the applications where this tension shows up tend to be the ones where failure isn’t an option.

The conventional answer has been to switch materials, redesign the part, or fall back to traditional composite layups, all of which add cost, time, or both. Spanish company Reinforce3D has been working on a different approach, one that’s starting to gain traction in North America.
Their technology is called Continuous Fiber Injection Process (CFIP), and the core idea is straightforward even if the engineering behind it is not. CFIP reinforces a part after it comes off the 3D printer, leaving the print process itself untouched.
Continuous fiber bundles are injected through internal channels that are designed into the part geometry from the start. The fibers follow the load paths of the component, reinforcing exactly the areas where stress concentrates. It’s a post-processing step that layers onto existing production workflows.
Reinforce3D also offers Design Checker, a software tool for planning and validating fiber paths before the part goes to print, helping engineers confirm that reinforcement channels are positioned along the right load paths before committing to production.

Reinforcing Parts Without Replacing 3D Printers
What makes this relevant to shops running HP MJF systems is that CFIP is designed to complement existing manufacturing workflows. The technology is described as compatible with 3D printed or machined parts, and the supplied case study demonstrates its use with standard FFF 3D printers.
As with any post-processing integration, fit with specific production setups is worth validating on a per-application basis. For manufacturers who have already invested in HP hardware and built their workflows around it, that matters. You’re adding a step to your line, not replacing one.
The most concrete example of what this looks like in practice comes from a recent VTOL drone project that Reinforce3D has documented. The airframe was printed in sections on standard FFF printers, then reinforced and joined using CFIP. Wings, landing legs, and tail assembly all received targeted fiber reinforcement.

The PA12 version of the drone, if produced using MJF or SLS, was projected to weigh around 330 grams, compared to 430 grams for the PETG version. The project also reported a total aircraft weight as low as 820 grams for the PA12 version, with a payload capacity of up to 600 grams.
The production numbers are worth noting too. Reinforcing each drone took about 50 minutes, and a setup running three FFF printers alongside one CFIP Delta Modular system could turn out a completed drone every eight hours.
Worth knowing, CFIP didn’t appear overnight. Reinforce3D spent the better part of a decade, from 2013 to 2021, developing the technology and locking down patents before launching the company and beginning industrial demonstrations in 2022. First customer installations followed in 2024.

CFIP Moves Into North American Markets
For North American manufacturers interested in evaluating the technology, the entry point is Impac Systems Engineering, a Temple, Texas-based firm that serves as Reinforce3D’s exclusive distributor in the United States and Canada.
Impac brings over 40 years of experience in additive manufacturing and industrial engineering, and they’ve installed a CFIP Delta system at their headquarters. Prospective customers can contact Impac to arrange a demonstration and discuss potential applications.
The broader picture here is a shift that’s been building for a while in additive manufacturing. Most shops solved the geometry challenge years ago. What still trips people up is getting printed parts to actually perform like the components they’re meant to replace.
Technologies like CFIP don’t solve that in every case, but for applications where continuous fiber reinforcement along load paths makes engineering sense, they offer a path that doesn’t require manufacturers to start from scratch.
If HP MJF production paired with post-print fiber reinforcement sounds like it might fit your application, Impac Systems Engineering can walk you through a live demonstration. Stop by Impac’s open house today and see the HP 1200 and 600 in person. Save your spot here.
To stay up to date with the latest 3D printing news, don’t forget to subscribe to the 3D Printing Industry newsletter or follow us on LinkedIn.
Explore the full Future of 3D Printing and Executive Survey series from 3D Printing Industry, featuring perspectives from CEOs, engineers, and industry leaders on the industrialization of additive manufacturing, 3D printing industry trends 2026, qualification, supply chains, and additive manufacturing industry analysis.
Featured image shows engineers reviewing fiber paths in Reinforce3D’s Design Checker software. Photo via Impac Systems Engineering.






